text.skipToContent text.skipToNavigation

HDR Relay, Heavy Duty, 1 pole

  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getAggregateRating, 26ms
  • REVIEWS, PRODUCT
  • bvseo-msg: The resource to the URL or file is currently unavailable.;

The HDR-11 is used for control of lighting circuits and other electrical loads in Wattstopper’s Peanut Panels, Lighting Integrator Control Panels and Lighting Management Control Panels. Momentary, low voltage signals from the panel’s control system switch the relays on or off. Mechanical latching operation results in lower power consumption and ensures the relay will remain in the last switched state in the event of a power loss. A built-in manual actuator allows the relay to be turned on or off in the event of a panel failure. The relay mounts into a standard 1/2” knockout and comes with a 5-pin phenolic connector for easy panel connection.
  • Send
  • Save as PDF
  • Add to favorites Remove from favorites

Features

  • Rated for up to 30A ballast lighting loads
  • 14,000A SCCR
  • Single pole, heavy duty power contacts
  • Mechanically latching relay
  • Built-in manual actuator
  • Five-pin pluggable connector for easy low voltage connection

Specifications

General Info
Product Line Wattstopper
UPC Number 754182939244
Country Of Origin China

Reviews

  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getReviews, 4ms
  • REVIEWS, PRODUCT
  • bvseo-msg: The resource to the URL or file is currently unavailable.;

Questions & Answers

Is there a low voltage relay that accepts larger wire that #10? Specifically #4 and #6 wire?

Asked by: Tyler
Hi Tyler, That is our standard relay that accepts wire gauge #10–#14 AWG, copper wire, solid, or stranded. Accepts 2-line and 2-load conductors. We do not carry one for larger gauge wires.
Answered by: Tier 1 Tech Support
Date published: 2023-08-09

What is the amp draw of the relay coil when switching ON or OFF?

Asked by: Mick
Hi Mick, These relays are rated for 20 amps maximum draw. The mechanically held, latching relays use two coils, and one or the other is energized momentarily to open or close the contacts. This design is extremely energy efficient. The relays draw power only when a coil is energized in response to a command to change state, thus they generate little heat, are inexpensive to operate and are inherently green devices. Please reach out to our tech. support team for further assistance if required. Legrand Technical Support: Phone: 1 800-879-8585, Option 3 then Option 1 Mon - Fri: 7am - 7pm CST (excluding holidays)
Answered by: Tier 1 Tech Support
Date published: 2023-03-01

how can I reverse the operation. the mall has a central panel and the store sign gets a signal to turn on, but the sign turns off. Later, the signal is to turn OFF and the sign turns ON.

Asked by: dave in NJ
More information is needed to properly answer your request. Please contact Wattstopper Technical Support @ 800-879-8585 for further assistance.
Answered by: Tier 1 Tech Support
Date published: 2022-08-05

is this a replacement for the HDR RELAY

Asked by: MJM question
The HDR-11 is the current replacement for older HDR relays.
Answered by: Tier 1 Tech Support
Date published: 2021-11-08

is this a replacement for the HDR-9 relay

Asked by: Nugz
Hi, Yes, The HDR-11 will replace an HDR-9.
Answered by: Tier 1 Tech Support
Date published: 2021-08-10

Will the HDR-11 relay replace the HDR-9?

Asked by: Anonymous
Thank you for contacting Wattstopper. Yes, the HDR-11 is a replacement for the HDR-9.
Answered by: Tier 1 Tech Support
Date published: 2021-07-23

Where can I buy this product?

Asked by: Anonymous
  • y_2024, m_3, d_18, h_10CST
  • bvseo_bulk, prod_bvqa, vn_bulk_3.0.38
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_7
  • loc_en_US, sid_HDR-11, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_legrand
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getContent, 7ms
  • QUESTIONS, PRODUCT